Find the accessory that you need for your Fluke 179:
Carrying Cases
Current Probes
Lights
Temperature Probes
Test Leads & Probes
Soft zippered carrying case with detachable external pouch. To be used with the 120-series, multimeters and testers.
For use with digital multimeters, power quality analyzers, and portable oscilloscopes, this current clamp allows users to take accurate current measurements without breaking electric circuits. Additionally, it measures up to 400 A AC.
Highly reliable, measures 1 to 1000 A, and provides accurate current reading without breaking the circuit. This clamp measures both AC and DC with a large jaw, battery-powered Hall-effect probe that gives access to difficult to reach areas.
A dual-range of 20 A and 200 A ac current clamp with voltage output via a safety insulated BNC connector. A dual banana to BNC adapter is supplied to allow the clamp to be connected to multimeters with banana inputs.
A single range 200 A clamp-on AC current clamp with current output via safety shrouded banana plugs. It is compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs.
Compatible with any temperature measuring instrument that accepts type K thermocouples and features a miniature connector input. Additionally, this surface temperature probe is ideal for measuring the temperature of flat or slightly convex surfaces, with an exposed junction to allow direct contact with the surface being measured.
Pair of red, black silicone test leads with right angle shrouded 0.16" (4 mm) banana plugs.
Features flexible silicone insulated leads are heat and cold resistant and are Cat I 30 V, 10 A rated.
DMM test leads (red, black) with safety shrouded, standard diameter banana plugs.
Provides five different ways to connect to terminals, this test lead set features 60" (1.5 m), silicone-insulated leads, useable from -112 to 158°F (-80 to 70°C), and is rated for 30 V, 8 A.
Ideal for high-energy environments. Additionally, this kit comes equipped with a probe extender and probe light, which allows users to illuminate those hard-to-reach areas.
Comes in a small and rugged design, this probe light kit liberates the users' hands for work. Additionally, it features a bright white LED and fits between the modular test probe and test lead.
Compatible with a variety of Fluke multimeters and test leads, this fused test probe set provides firm and secure contact.
Designed to extend the voltage measuring capability of an AC/DC voltmeter to 6000 V peak AC or DC Overvoltage Category I. The probe provides high accuracy when used with a voltmeter having 10 MΩ input impedance. Intended for low energy applications.
Designed to extend the voltage measuring capability of an AC/DC voltmeter to 15,000 V peak AC or DC Overvoltage Category I. The probe provides high accuracy when used with a voltmeter having 10 MΩ input impedance. Intended for low energy applications.
Designed to improve steadiness in slippery hands, and is for use with TL222 and TL224 test leads. Rubber over-molded surfaces and finger-hugging curves give a comfortable, reliable grip so you can focus on making an accurate measurement.
Comes equipped with one pair (red, black) of flat, right angle design for connecting to bus bars, and CAT III 600 V, 5 A rating, CSA listed. Adjustable collar provides two ranges of jaw openings up to 1.81" (30 mm).
Set of three (red, gray, black) safety designed insulated alligator clips for use with STL 120 Shielded Test Leads and TL75 Test Leads. Features a nickel-plated steel jaw contact material with a standard jaw opening of 5/16" (8 mm), and accepts standard 0.08" (2 mm) pin tip sized test probes.
Rugged, high-intensity Xenon worklight attaches to a baseball cap.
We accept these payment methods:
We also accept wire transfers/EFT, cheques and purchase orders on approved credit. Accepted payment methods vary by country.
