Home » Electrical » Electrical Combo Kits » Fluke 28-II TRMS Industrial Multimeter with IP67 Rating
Fluke 28-II TRMS Industrial Multimeter with IP67 Rating
Yes! Available up to 
USD 
The Fluke 28-II multimeter is the new standard for rugged
Fluke 28 II digital multimeter defines a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Fluke 28-II has an IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. This meter is built to work in the toughest environments.
Fluke 28 II digital multimeter defines a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Fluke 28-II has an IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. This meter is built to work in the toughest environments.
- Measure up to 1000 V ac and dc
- Measure up to 10 A (20 A for 30 seconds)10,000 μF capacitance range
- Frequency to 200 kHz
- Extended ac voltage bandwidth – 40 Hz to 30 kHz
- Resistance, continuity and diode test
- Min/Max and average recording to capture variations automatically
- Peak min-max
- Unique function for accurate
voltage and frequency measurements on adjustable speed motor drives and
other electrically noisy equipment
- IP 67 waterproof & dustproof protection, completely sealed for use in harsh environments
- Designed to withstand 3 meter drop (with holster)
- True-rms ac voltage and current for accurate measurements on non-linear loads
- Hi resolution 20,000 count display mode
- Backlit keypad buttons allow for easy visibility in lowlit areas
- Large display digits and 2 level bright white backlight for increased visibility
- Reversible holster for added protection when not in use
- Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards
- Long battery life (800 hours)
- Relative mode to remove test lead resistance from low ohms measurements
- Auto and manual ranging for maximum flexibility
- Optional magnetic hanger for easy setup and viewing while freeing your hands for other tasks
- MSHA approval (pending)
The Good:
The Bad:
The Bottom Line:
The Bad:
The Bottom Line:
Full Review
- Analog Bargraph
- Auto (Touch) Hold
- Auto Power Off
- Auto Ranging
- Backlight
- Backlight Keypad
- Capacitance
- Conductance
- Continuity
- Counts 19999 counts
- Counts 19999
- Current AC ac amps: 10a
- Current DC dc amps: 10a
- Dangerous Voltage Indicator
- Diode Test
- Display Hold
- Duty Cycle
- Frequency 200
- Input Alert
- Low Battery Indicator
- Low Input Impedance
- Low Pass Filter
- Manual Ranging
- Min/Max min/max/avg
- Min/Max/Avg
- Peak Transient Capture
- Relative Mode / Zero
- Resistance 50mω resistance
- Smoothing
- Temperature
- True RMS
- Voltage AC ac volts: 1000v
- Voltage DC dc volts: 1000v
- Waterproof/Dustproof
| Battery Life | 800 hours |
| Battery Type | 3x aa |
| CAT III Rating | 1000v |
| CAT IV Rating | 600v |
| Current AC Accuracy | 1.00% |
| Current DC Accuracy | 0.20% |
| Dimensions | 1.80 in x 3.95 in x 8.40 in (4.57 cm x 10.0 cm x 21.33 cm) |
| Peak Transient Capture | 250 µs |
| Temperature Accuracy | 1% |
| Voltage AC Accuracy | 0.70% |
| Voltage DC Accuracy | 0.05% |
| Warranty | lifetime |
| Weight | 1.14 lb (517.1 g) |
No user reviews available.
