Fluke 87V/E2 Industrial Electrician's Combo Kit

Model: 87-5/E2-KIT

Fluke 87V/E2 Industrial Electrician's Combo Kit in a soft case.

Add In House NIST Traceable Calibration to your 87-5/E2

Clear selected options


$521.99 USD

was $579.99

6 in Stock




 

  • True-rms ac voltage and current for accurate measurements on non linear signals
  • Selectable filter for accurate voltage and frequency measurements on motor drives
  • 0.05 % dc accuracy
  • 4-1/2 digit mode for precise measurements
  • Built-in thermometer lets you carry one less tool
  • Large display digits and two-level bright white backlight for increased visibility
  • 10,000 µF capacitance range for components and motor caps
  • Peak capture to record transients as fast as 250 µs
  • Measure up to 1000 V ac and dc
  • Measure up to 10 A, 20 A for up to 30 seconds
  • Auto and manual ranging for maximum flexibility
  • Analog bargraph
  • Resistance, continuity and diode test
  • Frequency to 200 kHz and % duty cycle
  • Min/Max and average recording to capture variations automatically
  • Relative mode to remove test lead resistance from low ohms measurements
  • Improved sleep mode for long battery life
  • Access door for fast battery changes without breaking the calibration seal
  • Limited lifetime warranty
  • Removable holster with built in test lead and probe storage
  • Cat IV 600 V and Cat III 1000 V electrical safety ratings
  • Basic test leads and alligator clips
  • Bead type thermocouple temperature probe

Correctly measure pulse-width modulated motor drive signals

Until now, there hasn't been a multimeter able to accurately measure adjustable speed drives. But the Fluke 87V is designed specifically to handle these complex signals. Think of the potential productivity you'll gain by taking the guesswork out of drive system troubleshooting. Measurements are correct each and every time.

  • Unique function for accurate measurements of noisy pulse-width modulated AC voltage.
  • Measures correctly at the ASD and at the motor terminals
  • Accurately measure the frequency (motor speed). Frequency measurement not affected by the ASDs carrier frequency
  • Measure AC current with an optional current clamp accessory
  • Compare reading from the 87V with the display on the ASD
  • Special shielding blocks high frequency, high-energy noise generated by large drive systems

Complex PWM drive signals are not a problem for the Fluke 87V
Pulse-width modulated detail of 50 Hz motor drive output voltage. 1000 V, 50 micro-second pulses can cause erratic behavior in some test equipment.

The Fluke 87V offers accuracy and diagnostics for maximum industrial productivity in the tool box or on the bench.

The Fluke 87V multimeter has improved measurement functions, troubleshooting features, resolution and accuracy to solve more problems on motor drives, in plant automation, power distribution, and electromechanical equipment.

With its newly incorporated selectable low pass filter, the Fluke 87V allows troubleshooters to take accurate voltage, current and frequency measurements on the output side of the drive at either the drive itself or the motor terminals.

The Fluke 87V/E2 Industrial Electrician Combo Kit makes troubleshooting more productive with standard meter hanging accessory for handsfree operation, soft case for protection and storage, 1.5 m heat resistant silicone test leads and more.

Features for maximum productivity

  • Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
  • Built-in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument
  • Large digit display with bright, two-level backlight

Electrical safety
All inputs are protected to Category III, 1000 V and Category IV 600 V. They can withstand impulses in excess of 8,000 V and reduce risks related to surges and spikes.

See the Fluke 87V - Industrial True-rms Multimeter with Temperature
Also available in an average responding multimeter, Fluke 83V

Specifications
Voltage DC
Maximum Voltage1000V
Accuracy ±(0.05%+1)
Maximum Resolution10 µV
Voltage AC
Maximum Voltage1000V
Accuracy±(0.7%+2) True RMS
AC Bandwidth20kHz*

*with low pass filter; 3db @ 1kHz
Maximum Resolution0.1 mV
Current DC
Maximum Amps10A (20 A for 30 seconds maximum)
Amps Accuracy±(0.2%+2)
Maximum Resolution0.01 µA
Current AC
Maximum Amps10A (20 A for 30 seconds maximum)
Amps Accuracy±(1.0%+2) True RMS
Maximum Resolution0.1 µA
Resistance
Maximum Resistance50 MΩ
Accuracy±(0.2%+1)
Maximum Resolution0.1Ω
Capacitance
Maximum Capacitance9,999 µF
Accuracy±(1%+2)
Maximum Resolution0.01 nF
Frequency
Maximum Frequency200 kHz
Accuracy±(0.005%+1)
Maximum Resolution0.01 Hz
Duty Cycle
Maximum Duty Cycle99.9%
Accuracy±(0.2% per khz +0.1%)
Maximum Resolution0.1%
Temperature Measurement
-200.0°C - 1090°C
-328.0°F - 1994.0°F
excluding probe
80 BK Temperature Probe

-40.0°C - 260°C

-40.0°F - 500°F, 2.2°C or 2% whichever is greater
Conductance
Maximum Conductance60.00 nS
Accuracy±(1.0%+10)
Maximum Resolution0.01 nS
Diode

Range 3 V
Resolution1 mV
Accuracy± (2 % + 1)
Duty Cycle Range
AccuracyWithin ± (0.2% per kHz + 0.1 %)

Environmental Specifications
Operating Temperature

-20°C to +55°C
Storage Temperature

-40°C to +60°C
Humidity (Without Condensation)

0% - 90% (0°C - 35°C)

0% - 70% (35°C - 55°C)
Operating Altitude

2000 m

Safety Specifications
Overvoltage category

EN 61010-1 to 1000 V CAT III, 600V CAT IV
Agency Approvals

UL, CSA, TV, VDE listed

Mechanical & General Specifications
Size

201 x 98 x 52 mm (with holster)
Weight

355 g
Weigh With Holster and Flex-Stand

624 g
Display
Digital6000 counts updates 4/sec.

(Model 87 also has 19,999 counts in high-resolution mode.)
Analog32 segments, updates 40/sec.
Frequency19,999 counts, updates 3/sec at > 10 Hz.
Warranty

Lifetime
Battery Life
Alkaline~400 hours typical, without backlight
Shock

1 Meter drop per IEC 61010-1:2001
Vibration

Per MIL-PRF-28800 for a Class 2 instrument
Click here for complete specifications on the Fluke 87-5/E2-KIT

  • Fluke 87V Industrial Multimeter
  • Fluke AC220 retractable long reach alligator clips
  • Fluke C35 lightweight soft case to provide optimal protection and storage
  • Fluke TPAK ToolPak meter haning accessory to hold meter to steel surfaces
  • Fluke TL224 1.5 m silicone leads resist head
  • Fluke TP238 removable probes with 4 mm of exposed metal to use on industrial circuits
  • 9V battery (installed)
  • Getting Started Manual
  • Info-pack and quick reference card
  • Fluke 80BK K-type temperature probe

Accessories

Click on a category to view a selection of compatible accessories with the Fluke 87V/E2 Industrial Electrician's Combo Kit.

Fluke C550 Premium Tool Bag C550 1447
Tool Bag with steel reinforced frame.
$99.99 USD

Learn More



Fluke C25 Large Soft Case C25 1437
For use with Fluke Multimeters.
$39.99 USD

Learn More


Fluke TLK225 SureGrip Master Accessory Kit TLK-225 2032
Kit includes Fluke AC220, AC280, AC283, AC285, TP175, and TL224 all in a 6-Pocket Storage Pouch.
$143.99 USD

was $159.99


Learn More

Fluke AC280 SureGrip Hook Clips AC280 1401
Rigid, Insulated, Shrouded Banana Jacks. Pair of Black and Red.
$34.99 USD

Learn More

Fluke TL81A Deluxe Electronic Test Lead Set TL81A 2010
Test Lead Set in quad-fold nylon pouch works with DMMs that accept safety shrouded, standard diameter banana connectors.
$134.99 USD

was $149.99


Learn More

Fluke TL935 Patch Cord Kit TL935 2026
Kit of 60, 90, and 120cm cords. 30V RMS or 60V DC, and 15A.
$49.99 USD

Learn More


Fluke TL26A 60 in. Telecom 5-Way Test Lead Set TL26A 1999
60" (1.5m), silicone-insulated leads, useable from -80 to 150°C (-112 to 302°F). Rated for 30V, 10A. One red, one black.
$59.99 USD

Learn More

Fluke TP1 Slim Reach Test Probe Set TP1 2040
For probing closely spaced or recessed terminals designed to hold securely in blade type electrical wall sockets.
$19.99 USD

Learn More

Fluke AC283 SureGrip Pincer Clips AC283 1402
Flexible, Insulated, Shrouded Banana Jacks. Pair of Black and Red.
$44.99 USD

Learn More

Fluke TLK291 fused test probe set TLK291 4630
For use with Fluke multimeters and test leads.
$79.99 USD

Learn More

Fluke TL910 Electronic Test Probe Set TL910 2012
Comfortable and allows accessibility to hard to reach test points.
$69.99 USD

Learn More

Fluke TL940 Mini-Hook Test Lead Set TL940 2027
30V RMS or 60V DC, and 15A.
$24.99 USD

Learn More


Fluke TL40 Retractable Tip Test Lead Set TL40 2004
Adjustable to desired length from 0 to 76mm.
$44.99 USD

Learn More

Fluke TP2 Slim Reach Test Probe Set TP2 2044
For probing closely spaced or recessed terminals compatible with AC72.
$19.99 USD

Learn More

Fluke TL220 Suregrip Industrial Test Lead Set TL220 1990
Includes Fluke AC220, Fluke TP220, and Fluke TL224.
$79.99 USD

Learn More

Fluke AC285 SureGrip Large Alligator Clip AC285 1403
Large alligator clip for test leads used with Fluke meters.
$24.99 USD

Learn More

Fluke TL930 Patch Cord Set (60 cm) TL930 2024
30V RMS or 60V DC, and 15A.
$19.99 USD

Learn More

Fluke TL950 Mini-Pincer Test Lead Set TL950 2028
30V RMS or 60V DC, and 15A.
$44.99 USD

Learn More

Fluke TL225 SureGrip Stray Voltage Adapter Test Lead Kit TL225 2646
Voltage Adapter Test Lead Kit makes sure the meter has a low input impedance that eliminates stray voltages and indicates real voltage.
$107.99 USD

was $119.99


Learn More

Fluke TL71 Premum DMM Test Lead Set TL71 2005
Comfort grip probes with silicone insulated, right-angle test leads.
$29.99 USD

Learn More

Fluke TP220 SureGrip Industrial Test Probes TP220 2045
For use with TL222 and TL224 test leads provides reliable contact.
$19.99 USD

Learn More

Fluke TL221 Suregrip Silicone Test Lead Extension Kit TL221 1992
Test Lead Extension Kit designed to improve steadiness with rubber overmolded surfaces and finger-hugging curves.
$29.99 USD

Learn More

Fluke AC87 Heavy Duty Bus Bar Clip Set AC87 1411
Insulated, Shrouded Banana Jacks. Pair of Black and Red.
$44.99 USD

Learn More

Fluke L210 Probe Light Kit L210 1835
L200 Probe Light and Probe Extenders.
$44.99 USD

Learn More

Fluke TL960 Micro-Hook Test Lead Set TL960 2029
30V RMS or 60V DC, and 15A.
$29.99 USD

Learn More

Fluke TL75 Hard Point Test Lead Set TL75 2007
Comfort grip probes with PVC insulated, test leads with right-angle shrouded banana plugs.
$24.99 USD

Learn More

Fluke 80K-40 High Voltage Probe 80K-40 1367
High Voltage Probe for Digital Multimeters, 40kV DC, 28kV AC.
$197.99 USD

was $219.99


Learn More

Fluke TP4 Slim Reach Test Probe Set TP4 2049
Designed to fit securely into IEC electrical wall outlets.
$19.99 USD

Learn More

Fluke TL222 SureGrip Silicone Insulated Test Leads TL222 1993
Test Leads designed to improve steadiness with rubber overmolded surfaces and finger-hugging curves.
$29.99 USD

Learn More

Fluke AC89 Heavy Duty Insulation Piercing Test Clip AC89 1412
Insulated, Shrouded Banana Jack. One Red.
$44.99 USD

Learn More


Fluke TL970 Hook and Pincer Kit TL970 2030
Kit includes TL940 Mini-Hook Test Lead Set, TL950 Mini-Pincer Test Lead Set, and TL960 Micro-Hook Test Lead Set.
$89.99 USD

Learn More

Fluke TL76 All-in-one Test Lead Set TL76 2008
2mm/4mm 1.5 meter long silicone test leads with right angle shrouded banana plug.
$34.99 USD

Learn More

Fluke 80K-6 KV High Voltage Probe 80K-6 1368
High Voltage Probe for Digital Multimeters, 6kV DC/AC.
$116.99 USD

was $129.99


Learn More


Fluke TL223 Suregrip Electrical Test Lead Set TL223 1994
includes Fluke AC220, TP1, TL224.
$79.99 USD

Learn More

Fluke TLK-220 US SureGrip Industrial Test Lead TLK-220 2031
Set includes AC220, AC285, TP220, and TL224 in zippered vinyl carry case with moveable divider.
$134.99 USD

was $149.99


Learn More

Fluke AC220 SureGrip Alligator Clips AC220 1400
Designed to improve steadiness with rubber overmolded surfaces and finger-hugging curves.
$44.99 USD

Learn More

Fluke TL80A Basic Electronic Test Lead Set TL80A 2009
1 meter long silicone test lead set, alligator clip and probe tip extender in a soft carrying case.
$79.99 USD

Learn More

Fluke TL932 Patch Cord Set 36" (90 cm) TL932 2025
36" (90 cm) (30V rms or 60V DC, 15A).
$19.99 USD

Learn More


Fluke TL224 SureGrip Silicone Insulated Test Leads TL224 1995
Designed to improve steadiness with rubber overmolded surfaces and finger-hugging curves.
$29.99 USD

Learn More


Fluke 80PK-24 SureGrip Air Temperature Probe 80PK-24 1374
K-Type, Air and Gas Temperature Probe.
$107.99 USD

was $119.99


Learn More

Fluke 80PK-25 SureGrip Piercing Temperature Probe 80PK-25 1375
K-Type, Piercing Temperature Probe, SureGrip.
$107.99 USD

was $119.99


Learn More

$107.99 USD

was $119.99


Learn More

Fluke 80PK-27 SureGrip Industrial Surface Temperature Probe 80PK-27 1377
K-Type, Industrial Surface Temperature Probe.
$296.99 USD

was $329.99


Learn More

Fluke 80PK-8 Pipe Clamp Temperature Probe 80PK-8 1381
Pipe Clamp Temperature Probe.
$161.99 USD

was $179.99


Learn More

Fluke 80PK-22 SureGrip Immersion Temperature Probe 80PK-22 1373
Type K Immersion Temperature Probe designed with a superior gripping surface made from thermoplastic rubber.
$99.99 USD

Learn More

Fluke i410 AC/DC Current Clamp I410 1826
1 to 400 Amps DC/1 to 400 Amps AC. For use with digital multimeters, scope meters and power quality analyzers.
$242.99 USD

was $269.99


Learn More

Fluke i410-KIT AC/DC Current Clamp with Carrry Case I410-KIT 1827
Included with kit: Fluke i410 (1-400A AC RMS, 1-400A DC Current Clamp) and a Zippered vinyl carry case with moveable divider.
$278.99 USD

was $309.99


Learn More

Fluke i200 AC Current Clamp I200 1554
Fuke i200 AC Current Clamp 1 A to 200A compatible with most Fluke multimeters or any other current measurement device that accepts shrouded banana plugs.
$143.99 USD

was $159.99


Learn More

Fluke i1010 AC/DC Current Clamp I1010 1821
For use with Digital Multimeters and Calibrators. Features a Current Range of 1A to 600A AC and 1A to 1000A DC.
$382.49 USD

was $424.99


Learn More

Fluke i400 AC Current Clamp I400 3542
1 Amp to 400 Amps for use with DMMs.
$143.99 USD

was $159.99


Learn More

Fluke i1010-KIT Current Clamp Kit I1010-KIT 1822
Includes carrying case.
$404.99 USD

was $449.99


Learn More

Fluke i2000 FLEX Flexible AC Current Probe I2000-FLEX 1823
2000A flexible AC current transformer for Fluke power quality analyzers.
$359.99 USD

was $399.99


Learn More

$427.49 USD

was $474.99


Learn More

Fluke L200 Probe Light L200 1831
Easily attaches to any Fluke test probe.
$29.99 USD

Learn More

$472.49 USD

was $524.99


Learn More

Fluke 80AK-A Thermocouple Adapter 80AK-A 1361
To be used with DMMs and Temperature Probes with K-Type Connector
$29.99 USD

Learn More


Ask a question about the Fluke 87V/E2 Industrial Electrician's Combo Kit:

comments powered by Disqus

Review the Fluke 87V/E2 Industrial Electrician's Combo Kit

" data-description="Fluke 87V/E2 Industrial Electrician's Combo Kit in a soft case.">